回首页

Tibbit模块列表

Four directly exposed I/O lines of the microcontroller.
Three directly exposed I/O lines of the microcontroller plus the ground line.
Two directly exposed I/O lines of the microcontroller plus the +5V output and ground lines.
Simple RS232 port with only TX, RX, RTS, and CTS lines.
Universal RS232/422/485 port with electronic mode selection.
Two mechanical low-power relays with independent normally opened terminals.
Two mechanical low-power relays with middle (common) terminals. Relay 1 has normally closed and normally opened terminals. Relay 2 only has the normally opened terminal exposed.
Two optically isolated inputs with independent terminals. Inputs are fully isolated from system ground.
Three optically isolated inputs with common (-). Inputs are fully isolated from system ground.
Three optically isolated inputs with common (+). Inputs are fully isolated from system ground.
Four opto-couple inputs with the '-' terminal connected to the system ground, independent '+' terminals.
Two optically isolated inputs with independent terminals. Inputs are fully isolated from system ground.
Three optically isolated inputs with common (-). Inputs are fully isolated from system ground.
Three optically isolated inputs with common (+). Inputs are fully isolated from system ground.
Four opto-couple inputs with the '-' terminal connected to the system ground, independent '+' terminals.
#05
RS485 port with full-duplex or half-duplex operation.
Two mechanical high-power relays with normally opened and normally closed terminals.
Two solid state normally opened relays.
Wiegand and clock/data reader port plus one open collector output.
Low-power non-isolated power supply with 5V output, 9-18V input range, shutdown control.
Medium-power non-isolated power supply with 5V output, 9-18V input range, and shutdown control.
Four open collector outputs.
Low-power non-isolated power supply with +15/-15V output, 5V input, shutdown control.
Four-channel ADC with -10V ~ +10V range.
Four-channel DAC with -10V ~ +10V range.
High-voltage AC solid state normally opened relay.
Three PWMs with open collector outputs.
Three PWMs with power outputs (the power must be supplied externally).
#18
Power jack and two terminal blocks.
DB9M connector.
Nine terminal blocks.
Four terminal blocks.
RTD temperature meter.
Isolated PoE power supply with 5V output, shutdown control. Also can be used as generic isolated power supply with 35-60V input range.
High-power non-isolated power supply with 5V output, 8-60V input range, and shutdown control.
Records and plays back infrared commands (codes) of conventional IR remote controls.
Infrared receiver circuitry and transmitter diode.
Visible spectrum ambient light sensor.
Ambient temperature meter.
Ambient humidity meter.
#31
ADC, PWM, I/O based on PIC 16F1824 microprocessor.
Barometric pressure sensor.
3-axis accelerometer (shock sensor).
#37
RF connector.
#38
One pushbutton.
Large green LED (low brightness)
Large red LED (high brightness)
Large yellow LED (low brightness)
Large blue LED (high brightness)
Digital potentiometer, 5KOhm, 8-bit resolution.
Digital potentiometer, 10KOhm, 8-bit resolution.
Digital potentiometer, 50KOhm, 8-bit resolution.
Digital potentiometer, 100KOhm, 8-bit resolution.
8-bit port (supplied with 200mm cable).
Real-time clock and non-volatile memory with backup battery and interrupt output.
#47
GPRS modem.
#48
Audio In/Out Tibbit
Micro SD card slot
Mini-B USB port with OTG
#51
CAN Bus

M1S

CAN bus transceiver with isolated power
Four-channel isolated ADC with -10V ~ +10V range.
Two-channel isolated ADC with 4 ~ 20mA range.
Four dry contact inputs; external switches should be installed between the input terminals and the system ground.
Type A USB port
#57
Contains an ICE5LP1K-SWG36ITR50 FPGA from Lattice Semiconductor
Two 24V NPN isolated open collector outputs
Two 24V PNP isolated open collector outputs